![double sided tape for woodworking home depot double sided tape for woodworking home depot](https://m.media-amazon.com/images/S/aplus-media/sc/500447d2-6bd2-4f90-943e-34d2e13864e0.__CR0,0,970,600_PT0_SX970_V1___.jpg)
I do some pattern routing, I need a tape there on occasion, for the shaper there is not a tape alive I'd trust to hold the work to a template when my hands are involved, its solid hold downs and stops there, destaco's on a jig. I don't do any turning, so I don't need that kind of adhesion. Well this DCP-02 looks like just the thing, and the price is more than reasonable. I'm pretty sure looking at my records that I bought the last batch from Highland Hardware, real easy to rip by hand, holds aggressively but not so much that it ruins work, never an issue with residue come finishing time. I've used spec brand, thats a little pricy but performs pretty well, I've used the wood craft brand too, saw a price when looking of $19/per roll for 3/4".who do they think they are kidding? If I bought tape like that I wouldn't have any money left for wood! Ouch. I use a tape at work with a blue plastic backing, very sticky, hard to remove from work, nearly destroys templates when removing, will lift mahogany grain randomly, and the blue backing is nearly impossible to peel, plus you have to cut it with a sharp knife, tough cloth stuff, nasty product. Jim, that looks and reads just like the one I've been using, thanks much for that link. JVCC DCP-02 Double Coated Crepe Paper Tape (Acrylic Adhesive) It's not ideal but doesn't leave you with sticky residue on either surface or trying to scrape the foam off if it's foam-filled. I've found plenty of double-stick that holds like the dickens I'm looking for something that lets go easier.įor all, as a work-around using overly-sticky tape, I've learned to put clear packing tape on my pieces (ideally with one ended reaching beyond the joint and folded over to give a handle) and use double-stick to hold those together. Was there any information on whether it was the DCP-01 (rubber adhesive) or DCP-02 (acrylic adhesive)?
![double sided tape for woodworking home depot double sided tape for woodworking home depot](http://www.woodworkersjournal.com/wp-content/uploads/Finishing-Tape-Lead.jpg)
No affiliation, just a very satisfied customer." It was on Brazilian Cherry(not an easy wood to sand) and very small pieces of the tape held the small strip (7" X 1/2" x 1/2") in place. Using oscillating spindle sander to sand out arcs. Last night I was shaping small parts for a small box base. The trick is also gradually finding out how much/or little is needed to hold items in place. Holding sandpaper onto a block/cork/soft back, etc. In fact, it's so easy to use, I find myself finding new ways to use it. Holds firm but releases without too much pressure and leaves no residue. I found it and have been using it for about a year and it works great. I read on a thread here(don't remember exact one) about a double sided tape that is a crepe type paper with adhesive. "I used to try and use double sided carpet tape and any other double sided tape I could find at local big box stores.
![double sided tape for woodworking home depot double sided tape for woodworking home depot](https://nomearo.com/wp-content/uploads/2018/08/18553-1.jpg)
It's been another year and this is still the best double sided tape I have ever used. More tape would have helped.The below is from another thread on same subject. I had tape in the centre of the four sides for this test. However it did move a couple of times which wrecked jobs. XFasten worked well and left only a small amount of residue.The jobs differed a little from each other but here are some general observations: The carpet tapes were quite strong but also quite thin which was a downside for me because the top of my wasteboard is typically uneven.The Xfasten was harder to pull up than the LLPT because of the construction of the tape.Here are a few notes from my observations. Residue and Surface FinishĪfter attaching the tape for 15 minutes, then pulling it off different materials the tapes were very similar across the board. I also have notes here form using the different tapes on the jobs I was doing on the CNC. I did attempt to do some base level testing (see images above). I liked using it and for the right job (small and repetitive) it is a good choice but i probably wouldnt’ buy again.Īvailable Here – Trazon Carpet Tape Double Sided Width It is also a little more expensive than the others. However, I didn’t think it was as sticky which means you need more per part. Because of this It is also easier to use more than once. This silicone based backing makes this tape easier to pull off and on than the Xfasten. LLPT Double Sided Woodworking Tape WidthĢ5mm (1″), (also available in 35, 45, 55 & 65mm) I received 3 rolls in the pack as all the other tapes came as a single roll.Īvailable here – XFasten Double Sided Woodworking Tape 2. There was a slight pulling up of grain (which is hard to see in the images) but it is very minimal. It also peels off with no stickyness left on the material (even after being stuck for an hour.) It isn’t as strong as epoxy, but it does have good sticking power. When I tested the different tapes, it had great sticking power. It will join to itself which can make using it more than once a little difficult. It’s is like thin cloth when using it because it isn’t rigid at all.